Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
Listed here in the next paragraph you might get a bunch of sound insight when it comes to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the task can move quickly; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is better to consider utilizing one before you start. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you mount a new bathtub in your washroom if you have currently gotten a brand-new bathtub as well as do not need to transform the arrangement of your previous water pipelines.
Your devices as well as material list ought to comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The process of removing the existing taps can be rather problematic because of the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in place with the producer offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous kind needs to be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Activate the water and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise check the overflow outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub should wait until the bath tub has actually been utilized a minimum of once as this will settle it right into its last setting.
Preparing for the Installment
First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that article on How to Install a Bathtub from an acquaintance on a different web blog. Do you know somebody else who is fascinated by the niche? Take a moment to share it. Bless you for your time. Visit again soon.
Pricing Report this page